PTFE, PFA, FEP, PVDF Fluoroplastic products industry experts
FEP film
Classification:
FAQ
Author:
PTFE tube little sister
Source:
PTFE tube little sister
Release time:
1999-08-10
Visits:
FEP film
FEP full name is Fluorinated ethylene propylene, translated as fluorinated ethylene propylene copolymer (perfluorinated ethylene propylene copolymer) English trade name: Teflon * FEP, is a class of chemical substances.
FEP is a copolymer of tetrafluoroethylene and hexafluoropropylene. The FEP crystals had a melting point of 304 ° C. and a density of 2.15g/cc.
FEP can be applied to soft plastics, the tensile strength, wear resistance, creep resistance is lower than many engineering plastics. It is chemically inert and has a low dielectric constant over a wide range of temperatures and frequencies.
FEP film does not ignite, can prevent the spread of flame. It has excellent wear resistance and low friction coefficient, which can be used from low temperature to 392F.
The material can be made into granular products for extrusion and molding, as powders for fluidized beds and electrostatic finishes, and also into aqueous dispersions. Semi-finished products are tubes, films, plates, rods and single fibers.
Its main use is for the production of pipe and chemical equipment lining, drum surface and a variety of wires and cables, such as aircraft hook line, pressurized cable, alarm cable, flat cable and oil well logging cable. FEP films have been used as thin coatings for solar collectors.
F-46 resin has both the characteristics similar to polytetrafluoroethylene and the good processability of thermoplastics. Therefore, it makes up for the lack of processing difficulties of PTFE, making it a material to replace PTFE. In the production of wire and cable, it is widely used in electronic equipment transmission wires used at high temperature and high frequency, electronic computer internal connection wires, aerospace wires and special purpose installation wires, oil pump cables and submersible motor winding wires.
Shenzhen Dankai Technology Co., Ltd. (ShenZhen DanKai Technology Co., Ltd.), whose predecessor was the Fluoroplastic Material Factory of Dongguan Dandi Insulation Material Co., Ltd. established in 1998, specializes in the research and development, production and sales of FEP, PFA, PTFE and other fluoroplastic tube rod sheet membrane products and other insulation materials. The company has international standards of senior R & D team and the introduction of foreign fluorine plastic products production line. Some fluoroplastic products through ISO9001, SGS, FDA certification, Huawei, Foxconn, the United States, ZTE, Intel, AirTAC and other domestic and foreign cooperation customers fully affirmed. The company's main products are: ① pipes: Ptfe pipes, Fep pipes, Pfa pipes, Pvdf pipes; ② Heat shrinkable tubes: Ptfe heat shrinkable tubes, Fep heat shrinkable tubes, Pfa heat shrinkable tubes, Pvdf heat shrinkable tubes; ③ Plate rod film: Ptfe plate rod film, Feep plate rod film, Pfa plate rod film, Pvdf plate rod film, etc. PE: PE, special, spiral tube, spring tube, rotary cutting tube, welding rod, tee, straight, gasket, joint, cone rod, flared tube, sealing tube, braided tube, corrugated tube, etc. At the same time can be customized according to customer requirements processing production of various specifications of fluorine plastic products.
Key words:
Previous Page
Next Page
Previous Page
Next Page
Dankai Technology
Address: Area B, 4th Floor, Building 1, North Yongfa Science and Technology Park, Yanchuan North, Chaoyang Road, Songgang Town, Bao'an District, Shenzhen, China
Tel: +86-755-29979617 23127719 23127819
E-mail: dkt@szdankai.com
Focus on us
Copyright©2024 All rights reserved of Shenzhen Dankai Technology Co., Ltd.
